Home > Industry knowledge > Content
Categories / CATEGORY
contact us / CONTACT US

Shenzhen White Automation Equipment Co., Ltd.
Company Address: No. 7, Faqiang Road, Liulian Community, Pingdi, Longgang District, Shenzhen
Contact: Mr. Shen

Phone: 17722614040
Phone: 0755-84071674, 84071672
Fax:0755-84071675


E-mail:huaite@vip.163.com
Website: www.huaite.tm

Industry knowledge
Safe operation process of Shenzhen tape slitting machine
Edit:Shenzhen White Automation Equipment Co., Ltd.   PublicDate:2018-03-12

ShenzhenTape slitting machineSafe operation process

First, turn on

1. Turn on the electrical isolation switch (set in front of the electrical control cabinet), press the EMERCENCY STOP RESET and READY TO RUN buttons, the key opens the MACHINE to RUN (on the main operating platform) to check whether the voltage (380V), current is correct and stable.

2. Turn on the power switch of the hydraulic system (set on the main hydraulic drive frame), and check whether the oil level and pressure gauge of the main hydraulic drive system are correct and stable.

3. Open the pneumatic shut-off valve (set on the intake pipe under the pneumatic control cabinet), check whether the air pressure is correct (not less than 6.0bar) and stable.

2. Setting control

1. Set the cutting menu according to the film type, thickness, length, width, etc. arranged in the cutting plan.

2. File the corresponding BOPP film file from the PDF.

3. Set the winding length and width of the corresponding film.

4. Select the corresponding winding station, adjust the roller arm and roller, and install the paper core of corresponding specifications.

3. Feeding, film passing and film joining

1. Loading: According to the requirements of the cutting plan, according to the driving operation regulations, according to the actual situation, hang the corresponding parent roll on the aging frame, according to the direction of the inside and outside of the corona surface, place it on the unwinding frame of the cutting machine, and use the control button Clamp the steel core, leave the steel core support arm and drive.

2. Film penetration: When there is no film on the slitter, film penetration is required. Use the slitting device and function keys of the slitting machine to tie the original film to the eye of the film linking chain, and start the filming button, so that the film is evenly distributed on each roller along the slitting process.

3. Film connection: when there is film on the slitting machine, when changing the roll joint, use the vacuum film connection table to start the film connection table to the working position, manually flatten the film on the first traction roller of the cutting machine and start the upper vacuum pump to suck the film , So that the film is absorbed flat on the membrane receiving platform, attach double-sided tape and cut off the excess film under the tape, flatten the film on the unwinding rack and start the lower vacuum pump to make the film flat adsorption, remove the tape on the paper Layer and level the adhesive film, the joints should be neat and wrinkle-free, then turn off the upper and lower vacuum pumps, and open the film connection table to the non-working position.

Four, start-up operation

1. The specifications are changed, the paper core is installed on the inner and outer winding arms, and all the personnel are notified to leave the machine when the press roller is in the operation preparation state and ready for operation.

2. Put the ANTI-STAIC BARS on the main console to AUTO, READY TO RUN is turned on, start MACHINE RUN and start running.

5. Slitting control

In the process of slitting operation, carefully monitor and observe the effect of slitting, and properly adjust and control the slitting speed, unwinding tension, contact pressure, curved roller, edge material traction roller, guide edge, etc.

6. Receipt

1. When the machine stops running after the inner and outer ends are wound up, use the unloading button to place the film on the prepared film unloading trolley, cut the film and paste the film roll with sealing glue.

2. Use the chuck release button to loosen the chuck, check whether the paper core of each film roll is away from the paper core, and if one end is still stuck on the paper core, manually remove the film roll.

3. After ensuring that all the films leave the chuck and place on the trolley, use the film loading button to raise the winding arm, install the corresponding paper core, and attach the film neatly to the paper core for the next slitting.

7. Parking

1. When the film roll reaches the set length, the equipment automatically stops.

2. During the operation of the equipment, you can press MACHINE STOP to stop as needed.

3. When a quick stop is required, press the MACHINE STOP key greater than 2S.

4. When an emergency situation such as a device or human accident occurs, press EMERGENCY STOP for emergency stop.

Eight, matters needing attention

1.Shenzhen tape slitting machineBefore starting the machine, ensure that the voltage, current and hydraulic values ​​are correct and stable.

2. Before the equipment is ready for operation, all personnel must notify leaving the equipment to ensure personal safety before starting operation.

3. When the slitting machine is in operation, do not touch the film roll or roller core in operation with your hand, so as to avoid the risk of personal injury caused by the hand in.

4. During the operation, avoid scratching or cutting each roller core with a knife or hard object.